SN74HCT574DWRE4
| Parameters | |
|---|---|
| Number of Bits | 8 |
| Propagation Delay | 53 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| High Level Output Current | -6mA |
| Low Level Output Current | 6mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Ports | 2 |
SN74HCT574DWRE4 Overview
SOICis the packaging method. A package named Tape & Reel (TR)includes it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is powered from a supply voltage of 5V. The electronic device belongs to the HCTfamily. The electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. The clock edge trigger type for this device is Positive Edge. It is included in FF/Latches. The design is based on 8bits. To achieve this superior flexibility, 8 circuits are used. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. There are 5V power supplies attached to it. A D flip flop with 2embedded ports is available. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. In order for the chip to function, it has 1output lines. A total of 3input lines have been provided. -6mAis the output current at high level. In the low level output current setting, the current is set to 6mA. Ideally, the operating temperature should be below 85°C. The operating temperature should be higher than -40°C. The system operates with a minimum supply voltage of 4.5V. 5.5Vis the maximum supply voltage supported by it. It is possible to obtain a frequency of 40MHz. It uses the logic IC BUS DRIVER. As a result, it is equipped with 1 functions . The D latch is equipped with 20 pins.
SN74HCT574DWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74HCT574DWRE4 Applications
There are a lot of Texas Instruments SN74HCT574DWRE4 Flip Flops applications.
- Digital electronics systems
- Computing
- Guaranteed simultaneous switching noise level
- Buffered Clock
- Asynchronous counter
- Single Down Count-Control Line
- Automotive
- Reduced system switching noise
- Counters
- Count Modes
