SN74HCT574PWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 53 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 47ns @ 5.5V, 150pF |
| Prop. Delay@Nom-Sup | 45 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 27000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT574PWG4 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). The package Tubecontains it. It is configured with Tri-State, Non-Invertedas an output. The trigger it is configured with uses Positive Edge. Surface Mountis positioned in the way of this electronic part. The supply voltage is set to 4.5V~5.5V. The operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74HCTseries of FPGAs. It should not exceed 40MHzin terms of its output frequency. In total, it contains 1 elements. As a result, it consumes 8μA quiescent current and is not affected by external forces. A total of 20 terminations have been made. It is a member of the 74HCT574 family. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 3pFfarads. In terms of electronic devices, this device belongs to the HCTfamily of devices. A part of the electronic system is mounted in the way of Surface Mount. 20pins are included in its design. Its clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. This flip flop is designed with 8 Bits. Despite its superior flexibility, it relies on 8 circuits to achieve it. The D latch runs on a voltage of 5V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If high efficiency is to be achieved, the supply voltage should be maintained at 5V.
SN74HCT574PWG4 Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT574PWG4 Applications
There are a lot of Texas Instruments SN74HCT574PWG4 Flip Flops applications.
- EMI reduction circuitry
- Cold spare funcion
- Frequency division
- Divide a clock signal by 2 or 4
- Event Detectors
- Data Synchronizers
- Load Control
- Data storage
- Safety Clamp
- Asynchronous counter
