SN74LS273DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 21 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74LS273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 27 ns |
| Turn On Delay Time | 17 ns |
| Family | LS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 27mA |
| Current - Output High, Low | 400μA 8mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 5V, 15pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 2 |
| fmax-Min | 30 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 30000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74LS273DWR Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). It is contained within the Tape & Reel (TR)package. T flip flop uses Non-Invertedas its output configuration. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 4.75V~5.25Vis required for its operation. It is operating at a temperature of 0°C~70°C TA. This D latch has the type D-Type. It is a type of FPGA belonging to the 74LS series. You should not exceed 40MHzin the output frequency of the device. D latch consists of 1 elements. It consumes 27mA of quiescent current without being affected by external factors. A total of 20 terminations have been made. It is a member of the 74LS273 family. Power is supplied from a voltage of 5V volts. In this case, the D flip flop belongs to the LSfamily. There is an electronic part that is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device has the clock edge trigger type of Positive Edge. This RS flip flops is a part number FF/Latches. Flip flops designed with 8bits are used in this part. The superior flexibility is achieved through the use of 8 circuits. This D flip flop is well suited for TR based on its reliable performance. The D latch runs on a voltage of 5V volts. For high efficiency, the supply voltage should be set to 5V. With a current output of 8mA , it offers maximum design flexibility. This input has 2lines.
SN74LS273DWR Features
Tape & Reel (TR) package
74LS series
20 pins
8 Bits
5V power supplies
SN74LS273DWR Applications
There are a lot of Texas Instruments SN74LS273DWR Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Test & Measurement
- CMOS Process
- Registers
- Memory
- Pattern generators
- Shift registers
- EMI reduction circuitry
- Differential Individual
- Modulo – n – counter
