SN74LVTH273PWRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 150MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Load Capacitance | 50pF |
| Current - Output | 64mA |
| Propagation Delay | 3.2 ns |
| Turn On Delay Time | 3.2 ns |
| Family | LVT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| Prop. Delay@Nom-Sup | 4.9 ns |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVTH273PWRE4 Overview
The flip flop is packaged in TSSOP. As part of the package Tape & Reel (TR), it is embedded. T flip flop uses TTLas the output. There are 1 elements in it. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is powered by a voltage of 3.3V . A device of this type belongs to the family of LVT. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part you are looking for is included in FF/Latches. On the basis of its reliable performance, this D flip flop is well suited for use with TR. For high efficiency, the supply voltage should be set to 3.3V. -32mA is set as the high level output current. Low level output current is set to 64mA. Ideally, the operating temperature should be below 85°C. If the operating temperature is higher than -40°C, the system should operate properly. The system operates with a minimum supply voltage of 2.7V. In this case, it supports a maximum supply voltage of 3.6V. 150MHzis the maximum frequency that can be achieved. D FLIP-FLOPis the logic IC it uses. It is equipped with 1 functions . This device is equipped with a pin count of 20. As a result of its output current of 64mA, it is very flexible in terms of design.
SN74LVTH273PWRE4 Features
Tape & Reel (TR) package
20 pins
1 Functions
20 pin count
SN74LVTH273PWRE4 Applications
There are a lot of Texas Instruments SN74LVTH273PWRE4 Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Memory
- Asynchronous counter
- Safety Clamp
- ATE
- Instrumentation
- Pattern generators
- Consumer
- Common Clocks
- Storage registers
