SN75C1406N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 21 hours ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Line Driver or Receivers |
| Technology | BIMOS |
| Voltage - Supply | 4.5V~15V |
| Terminal Position | DUAL |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 75C1406 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Nominal Supply Current | 250μA |
| Logic Function | Receiver, Transceiver |
| Data Rate | 120 kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 3/3 |
| Driver Number of Bits | 3 |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 5V |
| Duplex | Full |
| Receiver Hysteresis | 1V |
| Number of Transceivers | 1 |
| Receive Delay-Max | 4000 ns |
| Negative Supply Voltage-Nom | -12V |
| Simplex/Duplex | Full Duplex |
| Supply Voltage1-Nom | 12V |
| Number of Receivers | 3 |
| Out Swing-Min | 8 V |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN75C1406N Overview
This driver chip is excellent for driving common LEDs due to its enhanced 16-DIP (0.300, 7.62mm) package.Tube package is used to mount this receiver.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.You can place this wide receiver to any Through Hole-type PCB or development board.It takes 4.5V~15V from the power supply to run this differential driver.As many as 3/3 receivers/drivers are eligible for use on this electronic part.IC receiver likes this one are designed for use in applications where operating temperatures are 0°C~70°C.5V is the supply voltage range that this line driver ic can efficiently operate with.Wide receiver has 16 terminations built in for driving or receiving signals from data.In this package, you will find 16 market-standard pinouts for this transceiver.Since the base part number 75C1406 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.It is a 16-pin driver IC with enhanced power dissipation controls.A dramatic reduction in package size is achieved through optical transceiver downsizing and high-density Through Hole mounting technologies.There is a capability of 3-bit resolution with this ic receiver.There is a voltage input supply of 5V required for the operation of this integrated circuit.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.There are 1 transceivers in total that this module isolated transceiver implements.There are 3 receivers inside.According to the datasheet, when you try to enhance the line driver ic performance using negative voltage, -12V would be ideal for this purpose.If this can transceiver has a dual supply voltage, you should select a power supply that is suitable for 4.5V outputs.
SN75C1406N Features
Tube package
16 pin count
16 pins
SN75C1406N Applications
There are a lot of Texas Instruments SN75C1406N Drivers/Receivers/Transceivers applications.
- Gigabit Ethernet
- Switches
- Point-to-point networking
- Thermal management
- Routers
- Cable network front end
- Wireless modems
- Switching system
- Wireless transmission
- Laser diode bonding
