TL031CP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIFET |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TL031 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 217μA |
| Nominal Supply Current | 280μA |
| Output Current | 40mA |
| Slew Rate | 5.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 1.1MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1100 kHz |
| Voltage Gain | 81.58dB |
| Average Bias Current-Max (IIB) | 0.0004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1.1MHz |
| Max I/O Voltage | 1.5mV |
| Power | NO |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL031CP Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. Buffer amps of this type are called J-FET-types. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be 8 terminations in the next few months. The total number of pins on linear amplifier is 8. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. There are 8 pins on this chip. In terms of input offset voltage, operational amplifier rates 3.5mV. Through Hole is the recommended mounting type of operational amplifiers. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . Using a supply current of 217μA , this buffer op amp will be able to operate. Keeping the voltage gain at 81.58dB is the best course of action. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of instrumentation amplifier is rated 15V voltage.
TL031CP Features
8 Pins
supply voltage of 5V
81.58dB voltage gain
TL031CP Applications
There are a lot of Texas Instruments TL031CP Instrumentational OP Amps applications.
- pH (acidity)
- High speed sample
- Thermocouples
- Inverse/same-phase proportional circuit
- Semiconductor detectors
- Car stereo
- Image computer boards
- Industrial control system
- Micro signal measurement
- Scintillation detectors
