TLV2344IN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | TLV2344 |
| Pin Count | 14 |
| Operating Supply Voltage | 4V |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Operating Supply Current | 2.7mA |
| Nominal Supply Current | 6.4mA |
| Power Dissipation | 1.575W |
| Output Current | 30mA |
| Slew Rate | 3.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.6pA |
| Voltage - Supply, Single/Dual (±) | 2V~8V ±1V~4V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 790 kHz |
| Gain Bandwidth Product | 1.7MHz |
| Unity Gain BW-Nom | 1700 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.002μA |
| Programmable Power | NO |
| Max I/O Voltage | 10mV |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2344IN Overview
There is a 14-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be 14 terminations in the next few months. The total number of pins on linear amplifier is 14. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 14 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. This electronic component is recommended to be mounted using the mounting type Through Hole. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . This op amp can operate from a supply current at 2.7mA. Keeping the voltage gain at 87.23dB is the best course of action. There are 4 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 4V voltage. In this case, LinCMOS? represents the instrumentation amplifiers' series number.
TLV2344IN Features
14 Pins
supply voltage of 5V
87.23dB voltage gain
TLV2344IN Applications
There are a lot of Texas Instruments TLV2344IN Instrumentational OP Amps applications.
- Fission chambers
- High/low-pass filter circuit
- PDA
- Portable electronic products powered by batteries
- Measurements of Wheatstone bridge
- E-book readers
- Division circuits
- Car stereo
- Fast A/D and D/A converters
- Active probe
