TPS40304DRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40304 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6.5V |
| Output Type | Transistor Driver |
| Max Output Current | 25A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Power Dissipation | 2.61W |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | 3V~20V |
| Quiescent Current | 2.5mA |
| Control Features | Enable, Power Good, Soft Start |
| Max Output Voltage | 18V |
| Topology | Buck |
| Min Input Voltage | 3V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 600kHz |
| Max Input Voltage | 20V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 20V |
| Min Output Voltage | 6.2V |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 660kHz |
| Duty Cycle (Max) | 90% |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40304DRCT Overview
This switching controller fits most application requirements since it is packaged in a 10-VFDFN Exposed Pad package. dc motor controller is suitable for 1 output generation. Tape & Reel (TR) is the solid enclosure in which PMIC is packaged. Transistor Driver dc switching's outputs (s) are supported. A 3V~20V voltage is supplied to the dc control and used for operating it. Workable in an dc switcher where -40°C~125°C TJ is the -40°C~125°C TJrm. Switching can be done at 600kHz with this switching controller. The Surface Mount value makes it suitable for general dc dc regulator. To provide efficient switching control, Enable, Power Good, Soft Start is included in the dcdc regulator. SWITCHING CONTROLLER analog IC connects the switch converters. There are a DUAL terminal on the switching converters. 10 terminations with a variety of function. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 12V is input. You can find other relevant dc to dc converter ics by searching "TPS40304". Total pins of switching converter are 10. Statistically, DC regulator outputs 6.5V volts. normally, the dc dc regulator's output current is 25A, which you should keep in mind when starting a project. This dc regulatorhas a max frequency of 660kHz. In dormant mode, 2.5mA is used. A nominal working status is achieved when the input voltage is set to 20V. In order to ensure the dc switcher's functionality, users must limit the voltage to 20V due to the dc switcher's maximum input voltage. A voltage of 3V must be present in the supply. DC switcher will not be able to provide an output current above 25A volts. Datasheets indicate that the switching converter can output 18V volts at its maximum. A voltage controller's lowest output voltage cannot be less than 6.2V.
TPS40304DRCT Features
Transistor Driver Outputs
Switching Frequency: 600kHz
Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
TPS40304DRCT Applications
There are a lot of Texas Instruments TPS40304DRCT DC to DC converter applications.
- Household control circuits
- PSRR circuits
- Ball screw pair
- Die casting equipment
- Domestic water pumps
- Computer rooms
- Plate bending machines
- Bending machines
- Access control systems
- Smart grid
