TS1872AIST
| Parameters | |
|---|---|
| Unity Gain BW-Nom | 1600 kHz |
| Voltage Gain | 97dB |
| Average Bias Current-Max (IIB) | 0.15μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 100μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.13μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS1872 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 560μA |
| Output Current | 68mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 70nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 1.8MHz |
TS1872AIST Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations approaches 8. There are a total of 8 pins on this op amp. This linear amplifier should be powered by an 1.8V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 8 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 1mV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . You can run this op amp ic on 500μA . 97dB should remain the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
TS1872AIST Features
8 Pins
supply voltage of 1.8V
97dB voltage gain
Output Type: Rail-to-Rail
TS1872AIST Applications
There are a lot of STMicroelectronics TS1872AIST Instrumentational OP Amps applications.
- Signal amplification
- Medical instruments
- Proportional counter tubes
- Industrial control system
- Car stereo
- Computer workstations
- Strain gauges
- Micro signal measurement
- Displayers for aircraft and air transportation control systems
- Proportional operation circuits
