TS3A4741DCNR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TS3A4741 |
| Pin Count | 8 |
| Operating Supply Voltage | 3V |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Max Supply Current | 75nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Bandwidth | 125MHz |
| Turn-Off Delay Time | 9 ns |
| On-State Resistance (Max) | 900mOhm |
| High Level Output Current | 100mA |
| Low Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 23pF 20pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 14ns, 9ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.63mm |
| Thickness | 1.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS3A4741DCNR Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-8. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 8. As a result of its 2 channels, this electronic component provides high-quality output. A 1.8V voltage supply should turn on and run the electronic component. The electronic part body is injected with 8 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Search with TS3A4741 if you are looking for analog multiplexer variants. An switch multiplexer with 900mOhm internal resistance has a value of 900mOhm. The functions of 8 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. An effective Single supply digital multiplexer. There should be 1.65V voltage fed to the electrical part below 1.65V. This analogue multiplexer requires a voltage of 1.6V~3.6V when it drains from a single voltage supply. If put voltage greater than 75nA on the device, damage may be caused to the analogue multiplexer. A voltage of 3V can be used to operate the electronic component. Operating 2 inputs is required. The transfer of data can be performed over 125MHz bandwidths.
TS3A4741DCNR Features
2 Channels
Switch Circuit: SPST - NO
Bandwidth: 125MHz
TS3A4741DCNR Applications
There are a lot of Texas Instruments TS3A4741DCNR Analog Switches & Multiplexers ICs applications.
- Public switching systems
- DVD-R
- 65 V DACs
- Battery Powered Systems
- Low-Voltage
- PCMCIA cards
- Switching Systems
- Precision test equipment
- Multiplexers
- Modems
