TS932IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS932 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 66μA |
| Output Current | 1.5mA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS932IDT Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. This is a General Purpose type op amp. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 8-pin op amp ic is included in the package. Op amp rates 10mV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~105°C. It is possible to operate this buffer amplifier from a supply current of 20μA . 120dB should remain the voltage gain. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. 2 elements make up the design of this buffer amplifier. TAPE AND REEL is adopted to pack the instrumentation amplifier.
TS932IDT Features
8 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
TS932IDT Applications
There are a lot of STMicroelectronics TS932IDT Instrumentational OP Amps applications.
- Tablets
- Industrial control system
- Commercial audio systems
- Broadcasting
- Weighing systems
- Differentiator circuits
- Polarized electrodes
- Power control
- Car stereo
- Band-stop filter
