UA741IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | UA741 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Elements | 1 |
| Operating Supply Current | 1.7mA |
| Nominal Supply Current | 2.8mA |
| Power Dissipation | 500mW |
| Output Current | 25mA |
| Min Input Voltage | 5V |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 10nA |
| Max Input Voltage | 40V |
| Voltage - Supply, Single/Dual (±) | 10V~44V ±5V~22V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.2μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 1mV |
| Dual Supply Voltage | 15V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UA741IDT Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. Instrumentation amplifier is delivered in a Cut Tape (CT) case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are located on this board. Please take in mind that op amp should be run at 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are located on the operational amplifiers. Op amp rates 5mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~105°C for optimal performance. An 1.7mA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 106.02dB is the best course of action. There are 1 elements in this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 20V voltage. The linear amplifier is packaged by using a TAPE AND REEL axis.
UA741IDT Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
UA741IDT Applications
There are a lot of STMicroelectronics UA741IDT Instrumentational OP Amps applications.
- Signal operation
- Computer workstations
- Oscilloscopes
- single/dual op amp sum and difference circuits
- Comparator
- PDA
- High-frequency data acquisition systems
- Portable docking station
- Proportional counter tubes
- Active probe
