VN772K13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | OMNIFET II™, VIPower™ |
| JESD-609 Code | e4 |
| Feature | Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 60mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | DC Motors, General Purpose, Relays |
| Subcategory | Motion Control Electronics |
| Max Power Dissipation | 6W |
| Technology | Power MOSFET |
| Voltage - Supply | 5.5V~36V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 1.27mm |
| Base Part Number | VN772 |
| Pin Count | 28 |
| Number of Outputs | 4 |
| Supply Voltage-Max (Vsup) | 36V |
| Power Supplies | 8/36V |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 5mA |
| Output Configuration | Half Bridge (2) |
| Power Dissipation | 6W |
| Output Current | 8.5A |
| Output Current per Channel | 9A |
| Supply Current-Max (Isup) | 7mA |
| Voltage - Load | 5.5V~36V |
| Fault Protection | Current Limiting, ESD, Open Load Detect, Over Temperature, Over Voltage, Short Circuit, UVLO |
| Rds On (Typ) | 120m Ω (Max) |
| Load Type | Inductive |
| Height Seated (Max) | 2.65mm |
| Length | 17.9mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VN772K13TR Overview
Tape & Reel (TR) is used to package H bridge.In order to save costs, H bridge is included in the 28-SOIC (0.295, 7.50mm Width) package.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 5.5V~36V.H bridge circuit is put into place according to the way of Surface Mount.When -40°C~150°C TJ is operating at a certain temperature, motor driver H bridge can function normally.There are lots of uses for H bridge motor driver, including DC Motors, General Purpose, Relays.H gate is mounted on the PCB using Surface Mount.Among full bridges specific characteristics is Status Flag.28 terminations are used to terminate transmission lines with H bridges that match their characteristic impedance.In a signal interface, the 28 pins serve as pronged contacts.Based on its base H bridge ic number of VN772, more closely related H bridge ics can be found.For the operation of the H bridge, a voltage supply of 13V is used.BRUSH DC MOTOR CONTROLLER has been incorporated as H bridge circuit's analog IC type.A H-bridge belonging to the OMNIFET II?, VIPower? series, it is an electronic H-bridge.Output and power supply pins have a current of 8.5A.It is through the 28 pins that the bridge driver can perform its specific functions.The output of this Hbridge is 4.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.A load of electricity is supplied by 8/36V.
VN772K13TR Features
Available in 28-SOIC (0.295, 7.50mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : VN772
VN772K13TR Applications
There are a lot of STMicroelectronics VN772K13TR Full Bridge Drivers, Half-Bridge Drivers applications.
- Desktop Computers
- Voltage Regulators for CPUs
- Voltage Regulators for DDR memory arrays
- Notebook Computers
- Non-V-Core
- Voltage Regulators for GPUs
- Bipolar stepper motor
- VTR
- Quad DC motor
- Telecom Microprocessor
