VNV35NV04TR-E
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | OMNIFET II™, VIPower™ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 11 |
| ECCN Code | EAR99 |
| Resistance | 10mOhm |
| Max Power Dissipation | 125W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | VNV35 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 30A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Element Configuration | Single |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 125W |
| Output Current | 30A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 12 μs |
| Switch Type | General Purpose |
| Rise Time | 2.5μs |
| Drain to Source Voltage (Vdss) | 40V |
| Fall Time (Typ) | 1.5 μs |
| Turn-Off Delay Time | 120 μs |
| Continuous Drain Current (ID) | 30A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 40V |
| Rds On (Typ) | 10m Ω (Max) |
| Drain to Source Resistance | 10mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 3.7mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VNV35NV04TR-E Overview
As a result, it is packaged in the form of a Tape & Reel (TR).In the PowerSO-10 Exposed Bottom Pad package, it is included.The mounting type of the LED driver is Surface Mount.General Purpose is the type of switch owned by it.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.The lighting driver is equipped with 1 outputs that can be used.The LED driving board operates at Not Required volts.It produces a maximum output voltage of N-Channel volts at its maximum output.It is part of the VNV35 family of LED drivers.As a result, there are 11 terminations.In order to operate, the 10 pins are used.As far as the lighting driver is concerned, there are 1 functions.As a result, the maximum output current is reduced to 30A in order to meet the operation requirements.Using a voltage of 5V allows for high efficiency.It is positioned in the direction of Surface Mount.Currently, the LED driving board has 10mOhm resistance.It is included in the OMNIFET II?, VIPower? series.When this case is used, the output current is set to 30A.In order to maximize efficiency, the supply voltage should be set to 18V.For its operation, a current of 100μA is required.
VNV35NV04TR-E Features
Supplied from 5V
Resistance of 10mOhm
VNV35NV04TR-E Applications
There are a lot of STMicroelectronics VNV35NV04TR-E Power Switches ICs applications.
- Smartphone and PDA
- Portable Devices
- Portable GPS Device
- HDD and SSD
- Hot Swap
- Storage Drives
- Various applications equipped with buttons
- Solid-State Drives
- Wearable Devices
- Mobile Communication Devices
