XC1765ESO8C
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Additional Feature | USED FOR STORING THE CONFIGURATION BITSTREAMS OF XILINX FPGAS |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | XC1765E |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Programmable Type | OTP |
| Memory Size | 65kb |
| Operating Mode | SYNCHRONOUS |
| Clock Frequency | 10MHz |
| Supply Current-Max | 0.01mA |
| Organization | 64KX1 |
| Output Characteristics | 3-STATE |
| Memory Width | 1 |
| Standby Current-Max | 0.00005A |
| Memory Density | 65536 bit |
| Parallel/Serial | SERIAL |
| I/O Type | COMMON |
| Memory IC Type | CONFIGURATION MEMORY |
| Height Seated (Max) | 1.7272mm |
| Length | 4.9276mm |
| Width | 3.937mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
XC1765ESO8C Overview
8-SOIC (0.154, 3.90mm Width) is used in this package.Packing on the outside is Tube.Licensed to operate in 0°C~70°C.OTP is the program that allows it to be programmed.There is a voltage of 4.75V~5.25V applied to the device.FPGA is mounted in Surface Mount.There is a limit of 65kb MB for the amount of data that can be stored.In addition to this part, you can search "XC1765E" for other similar parts.In order for it to function, it requires a voltage supply of 5V.There are different functions that can be applied on the 8 axis when it comes to terminating.In order to use this memory device, a maximum voltage of 5.25V should be used.FPGA is essential that a minimum voltage of 4.75V be supplied to the device in order for FPGA to function.A CONFIGURATION MEMORY memory chip like this is used for data storage.If you're reflow soldering, you shouldn't go above 225.The 8 pins are on the board.Through SERIAL-processing, data is transmitted from this memory to the CPU.In order for a memory chip to operate, it must not be subjected to a voltage greater than 0.01mA.The part comes with a set of 8 pins.Using a 10MHz frequency, this memory IC can work at high speeds.The memory's I/O is configured as COMMON.You should use a 5V power supply.Memory features USED FOR STORING THE CONFIGURATION BITSTREAMS OF XILINX FPGAS to better serve the need.
XC1765ESO8C Features
Operating temperature: 0°C~70°C.
OTP program capability.
CONFIGURATION MEMORY memory IC.
SERIAL processing.
COMMON I/O equipped.
XC1765ESO8C Applications
There are a lot of Xilinx Inc. XC1765ESO8C applications of configuration proms for FPGAs.
- mainframes
- networks
- eDRAM
- nonvolatile BIOS memory
- supercomputers
- workstations,
- embedded logic
- Cache memory
- hard disk drive (HDD)
- data buffer
