1P1G66QDBVRG4Q1
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Base Part Number | 1G66Q |
| Output | COMMON OUTPUT |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Propagation Delay | 2.6 ns |
| Turn On Delay Time | 14 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 7.2ns, 6.9ns |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 8.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 25Ohm |
1P1G66QDBVRG4Q1 Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~125°C TA. A total of 5 terminations have been recorded. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 2.3V, it should be turned on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. Multiplexers built on a SPST - NO switching circuit are built. If you are looking for variants of the digital switch, trying search with 1G66Q. Internally, this switch multiplexer has a resistance of 25Ohm. Datasheets for functions of 5 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 1.65V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. As far as the outputs go, this switch multiplexer utilizes COMMON OUTPUT of them. The transfer of data can be performed over 300MHz bandwidths. From the Automotive, AEC-Q100 series.
1P1G66QDBVRG4Q1 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
1P1G66QDBVRG4Q1 Applications
There are a lot of Texas Instruments 1P1G66QDBVRG4Q1 Analog Switches & Multiplexers ICs applications.
- Communication systems
- Audio and video switching
- PCMCIA cards
- Fault Tolerant Systems
- Frame Relay Equipment
- Fiber In The Loop (FITL)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Cellular phones
- Private Branch Exchange (PBX)
- Digital access cross connects
