54FCT244ATLB
| Parameters | |
|---|---|
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Number of Pins | 20 |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 1mA |
| Family | FCT |
| Logic Function | Buffer, Inverting |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 4 |
| Prop. Delay@Nom-Sup | 5.1 ns |
| High Level Output Current | -12mA |
| Low Level Output Current | 12mA |
| Control Type | ENABLE LOW |
| Length | 8.9mm |
| Width | 8.9mm |
| Thickness | 1.52mm |
| RoHS Status | Non-RoHS Compliant |
54FCT244ATLB Overview
All of the 2 elements are put into use. 20 terminations with different functions. Buffer IC reuqires a supply voltage of 5V. This buffer driver is part of the FCT family of parts. 20 pins are set with the electric part. Buffer IC is suitable for Surface Mount applications. Logical driver has 20 pins. Enhanced with 2 ports. The bus transceiver employs 4 bits for each element. Specifically, digital transciever is a kind of Bus Driver/Transceivers. The digital buffer starts up under ENABLE LOW control technology. In quiescent state, the electronic part uses 1mA. It is recommended to use a 5V power supply. To run the part safely and stably in a circuit, 5V recommends users apply 5V on the logical driver. Voltage buffer is capable of operating under temperature as low as -55°C. Digital buffer should operate with ambient temperature no higher than 125°C. Buffer driver outputs 12mA to its low level. In high level output mode, the electronic parts may conduct -12mA of current. Voltage used to run voltage buffer should be 4.5V at least. In regard to the maximum supply voltage, buffer driver is rated 5.5V. It is known as a BUS DRIVER logic IC. It is sufficient to make 8 outputs.
54FCT244ATLB Features
Bus Driver/Transceivers
High Level Output: 12mA
Low Level Output: -12mA
BUS DRIVER Logic IC
54FCT244ATLB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT244ATLB Buffers & Transceivers applications.
- Broadcast application
- Digital systems
- Point-to-point networking
- Satellite ground stations
- Transmission stations
- Radio transmission
- Single to Multimode Fiber Conversion
- Tuner
- Switching system
- Desktop radio
