54FCT374TLB
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 14 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 11 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.032 A |
| High Level Output Current | -12mA |
| Low Level Output Current | 32mA |
| Independent Circuits | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.52mm |
| Length | 8.9mm |
| Width | 8.9mm |
| Thickness | 1.52mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | LCC |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
54FCT374TLB Overview
The flip flop is packaged in a case of LCC. The number of terminations is 20. An input voltage of 5Vpowers the D latch. It is a member of the FCTfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. There are 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Flip flops designed with 8bits are used in this part. This D flip flop is well suited for TUBE based on its reliable performance. A total of 5V power supplies are needed to run it. The flip flop has 2ports embedded within it. For high efficiency, the supply voltage should be kept at 5V. As a result, it consumes 10μA of quiescent current without being affected by external factors. There is -12mA output current at the high level. There is 32mA output current at the low level. There should be a temperature below 125°Cduring operation. Ideally, the operating temperature should be greater than -55°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. There is a maximum voltage support of 5.5V. BUS DRIVERis used as the logic IC in this D flip flop. The T flip flop is equipped with 1functions . The D latch is equipped with 20 pins.
54FCT374TLB Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
54FCT374TLB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT374TLB Flip Flops applications.
- Buffered Clock
- Data Synchronizers
- Latch-up performance
- Memory
- Individual Asynchronous Resets
- Computers
- Shift Registers
- Storage registers
- Load Control
- Modulo – n – counter
