54FCT574ATDB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Quiescent Current | 10μA |
| Turn On Delay Time | 7.2 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.032 A |
| Screening Level | MIL-STD-883 Class B |
| Trigger Type | POSITIVE EDGE |
| High Level Output Current | -12mA |
| Independent Circuits | 1 |
| Height | 2.9mm |
| Length | 25.4mm |
| Width | 7.62mm |
| Thickness | 2.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
54FCT574ATDB Overview
It is packaged in the way of CDIP. JK flip flop uses POSITIVE EDGEas the trigger. There have been 20 terminations. A voltage of 5V provides power to the D latch. Electronic devices of this type belong to the FCTfamily. In this case, the electronic component is mounted in the way of Through Hole. The 20pins are designed into the board. The part is included in FF/Latches. An electronic part designed with 8bits is used in this application. In this case, the maximum supply voltage (Vsup) reaches 5.5V. An electrical current of 5V volts is applied to it. The flip flop has 2ports embedded within it. Quiescent current is consumed by the D latch in the amount of 10μA. Additionally, you may refer to the D latch's additional BROADSIDE VERSION OF 374. There is -12mA output current at the high level. There should be a temperature below 125°Cduring operation. Operating temperatures should be above -55°C. The minimal supply voltage is 4.5V. It adopts a logic IC of type BUS DRIVER. There are 1 functions available on the JK flip flop. There are 20 pins on the D latch.
54FCT574ATDB Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
54FCT574ATDB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT574ATDB Flip Flops applications.
- Differential Individual
- Circuit Design
- Divide a clock signal by 2 or 4
- Common Clocks
- Guaranteed simultaneous switching noise level
- Shift registers
- Parallel data storage
- Asynchronous counter
- Memory
- ESCC
