54FCT574TDB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 14 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 11 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.032 A |
| High Level Output Current | -12mA |
| Low Level Output Current | 32mA |
| Independent Circuits | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 25.4mm |
| Width | 7.62mm |
| Thickness | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
54FCT574TDB Overview
The package is in the form of CDIP. A total of 20terminations have been recorded. A voltage of 5V is used to power it. This D flip flop belongs to the family of FCT. There is an electronic part mounted in the way of Through Hole. As you can see from the design, it has pins with 20. In this device, the clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. Flip flops designed with 8bits are used in this part. The system runs on a power supply of 5V watts. The flip flop has 2ports embedded within it. High efficiency requires the supply voltage to be maintained at 5V. Despite external influences, it consumes 10μAof quiescent current. Additionally, you may refer to the additional BROADSIDE VERSION OF 374 of the electronic flip flop. There is -12mA output current at the high level. 32mAis set as the low level output current. A temperature below 125°Cshould be used for operation. It is recommended that the operating temperature is higher than -55°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. There is a maximum supply voltage of 5.5V. It uses BUS DRIVERas its logic IC. Currently, it is equipped with 1 functions . This device is equipped with a pin count of 20.
54FCT574TDB Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
54FCT574TDB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT574TDB Flip Flops applications.
- CMOS Process
- Registers
- Computing
- ESD performance
- Bounce elimination switch
- Frequency Divider circuits
- Single Down Count-Control Line
- Balanced 24 mA output drivers
- Automotive
- ATE
