54FCT574TLB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | LCC |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 14 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 11 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.032 A |
| High Level Output Current | -12mA |
| Low Level Output Current | 32mA |
| Independent Circuits | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.52mm |
| Length | 8.9mm |
| Width | 8.9mm |
| Thickness | 1.52mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
54FCT574TLB Overview
It is packaged in the way of LCC. Terminations are 20. Power is provided by a 5V supply. The electronic device belongs to the FCTfamily. Surface Mount mounts this electronic component. As you can see from the design, it has pins with 20. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. An electronic part designed with 8bits is used in this application. The system runs on a power supply of 5V watts. This D flip flop is equipped with 0 ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. Despite external influences, it consumes 10μAof quiescent current. In addition, you can refer to the additinal BROADSIDE VERSION OF 374 of the D latch. A high level output current of -12mAis set. In the low level output current setting, the current is set to 32mA. There should be a temperature below 125°Cduring operation. Ideally, the operating temperature should be greater than -55°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. The maximum supply voltage supported by the flip flop is 5.5V. The logic IC it uses is BUS DRIVER. It is equipped with 1 Functions . 20pins are provided on the D latch.
54FCT574TLB Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
54FCT574TLB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT574TLB Flip Flops applications.
- Safety Clamp
- Balanced Propagation Delays
- Memory
- Bus hold
- Computers
- Test & Measurement
- Frequency Divider circuits
- Count Modes
- Registers
- Instrumentation
