5962-9073102MEA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
5962-9073102MEA Overview
Shipping overseas is convenient due to the electrical component's packing in 16-CDIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -55°C~125°C TA. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. Multiplexers built on a SPST - NO switching circuit are built. Circuits number 4 make up this analogue multiplexer. There is 80Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 30V in normal situations. 10V should be the lowest voltage fed to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 15V operating voltages can be used with this electrical part.
5962-9073102MEA Features
1 Channels
Switch Circuit: SPST - NO
5962-9073102MEA Applications
There are a lot of Maxim Integrated 5962-9073102MEA Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Data switching
- Relay replacements
- MP3 players
- Modems
- Wireless Local Loop
- FTTH
- HDTV
- SDH
- Medical systems
