5962-9073703MPA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | SPST |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
5962-9073703MPA Overview
The electrical component comes in 8-CDIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. Mounted in Through Hole is this multiplexer. 2:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -55°C~125°C TA. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 8 series. Multiplexers built on a SPDT switching circuit are built. 1 circuits are used in this analogue multiplexer. As far as internal resistance is concerned, it has 35Ohm. Datasheets for functions of 8 pins are available. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. There should be 10V voltage fed to the electrical part below 10V. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. With a SPST analog IC integrated into the board. This electrical part is compatible with 18V operating voltages.
5962-9073703MPA Features
1 Channels
Switch Circuit: SPDT
5962-9073703MPA Applications
There are a lot of Maxim Integrated 5962-9073703MPA Analog Switches & Multiplexers ICs applications.
- Cross Connects
- CSU
- Channelized and Unchannelized DS3 applications
- Relay Replacement
- Battery-powered systems
- Audio and video signal routing
- Medical
- Video switching
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SONET/SDH ADM
