5962-9326701MPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
5962-9326701MPA Overview
Power management is mounted through 8 terminals. It is packaged with Tube. There are 1 functions included in this PMIC so that you can refer to them. On this supervisor, there is a series of 1 channels that can be found. In this PMIC, you can find 8-CDIP (0.300, 7.62mm) functions for your reference. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 240. During operation, the power ic is supplied with a voltage of 5V. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. By Through Hole, IC management has been mounted. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. Power management has a total of 8 pins. This power management has 8 pins. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1.2V. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). The recommended mounting type for IC management is Through Hole. We recommend setting the supervisors to -55°C~125°C TA degrees. During operation, this power management system outputs Push-Pull, Totem Pole. The power management's supply current is 500μA. The power management must be powered by 5V volts to function properly. A maximum supply temperature of 500μA can be used.
5962-9326701MPA Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500μA operating supply current
5962-9326701MPA Applications
There are a lot of Maxim Integrated 5962-9326701MPA Voltage Supervisors applications.
- Electronics installed in the vehicle
- WiFi router
- Satellite navigation
- Data storage applications
- Military electronics
- Electrical fire monitoring system
- Rechargeable batteries
- Battery-powered equipment
- emergency room
- Insulation fault location system
