5962-9459301MPA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Lead, Tin |
| Package / Case | Q |
| Surface Mount | NO |
| Number of Pins | 8 |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 900mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | AD8001 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Elements | 1 |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 6V |
| Power Dissipation | 900mW |
| Quiescent Current | 5mA |
| Slew Rate | 1000 V/us |
| Architecture | CURRENT-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 50 dB |
| Input Offset Voltage (Vos) | 2mV |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 6V |
| Low-Bias | NO |
| Micropower | NO |
| Min Dual Supply Voltage | 3V |
| Bias Current-Max (IIB) @25C | 25μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Input Bias Current | 3μA |
| Wideband | YES |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
5962-9459301MPA Overview
There is a Q case package that contains the instrumentation amplifiers. Buffer amps of this type are called OPERATIONAL AMPLIFIER-types. A Tube case is used for delivering the op amp. The number of terminations is approaching the 8 mark. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. This op amp needs to be operated at a temperature of not less than -40°C degrees Celsius in order to function properly. It is recommended that op amp be used at temperatures below 125°C. The op amp is rated for an operating supply voltage of 1. The operating supply voltage of instrumentation amplifier is rated 9V voltage. Regarding the voltage of the supply, this electrical part can work from a voltage as low as 12V, and this is an excellent feature. In order to ensure that the instrumentation amplifier's supply voltage remains above 6V, it is recommended to keep it higher. As a rule of thumb, you should conduct this electronic part under a dual voltage supply of 6V volts. There is a quiescent current of 5mA in this operational amplifier circuit.
5962-9459301MPA Features
8 Pins
supply voltage of 5V
5962-9459301MPA Applications
There are a lot of Analog Devices Inc. 5962-9459301MPA Instrumentational OP Amps applications.
- Micro signal measurement
- Cinema or auditorium audio system
- Information processing
- Inverse/same-phase proportional circuit
- Exponential operation circuits
- Division circuits
- Automotive sensors
- High speed sample
- pH (acidity)
- Hand-held batteries
