7200L15JI
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | PLCC |
| Number of Pins | 32 |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 32 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | RETRANSMIT |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 32 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Element Configuration | Dual |
| Nominal Supply Current | 80mA |
| Max Supply Current | 80mA |
| Clock Frequency | 40MHz |
| Access Time | 15 ns |
| Organization | 256X9 |
| Density | 2.3 kb |
| Standby Current-Max | 0.005A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Asynchronous |
| Word Size | 9b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| FWFT Support | No |
| Output Enable | NO |
| Cycle Time | 25 ns |
| Height Seated (Max) | 3.55mm |
| Length | 13.97mm |
| Width | 11.43mm |
| Thickness | 2.79mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
7200L15JI Overview
The PLCC package contains FIFO memory chip.Mounting it Surface Mount is recommended.An input voltage of 5V results in high efficiency.A total of 32 terminations are contained within FIFO means.There are 32 pins for operation.The maximum current required for its operation is 80mA .In order to maximize efficiency, the supply voltage should be set to 5V .This FIFO products runs at -40°C degrees Celsius at a minimum temperature to ensure reliability.Keeping the operating temperature at 85°C °C allows the FIFO products to operate continuously.The gadget in FIFOs is self-contained.A OTHER FIFO memory type IC is used in the part.There is a possibility that FIFO may operate at a very low supply voltage, such as 4.5V V.FIFO memory is capable of handling a maximum supply voltage of 5.5V volts.There are a total of 32 pins on this board.It is normal for a component to be equipped with 5V power supplies.It is also possible to generate RETRANSMIT with the use of this FIFO memory.A clock on the FIFO memory IC runs at a frequency of 40MHz .
7200L15JI Features
FIFOs category
Clock frequency of 40MHz
7200L15JI Applications
There are a lot of Integrated Device Technology (IDT) 7200L15JI FIFOs Memory applications.
- Signal processing
- Data-acquisition systems
- Video time base correction
- IP Radio
- Desktop Computers
- Consumer Systems
- Controlled baseline
- MP3 Interface for Automobile
- GPS Offender Tracking
- SPI Bus Flash Memory Device
