7201LA30DB
| Parameters | |
|---|---|
| Packaging | Bulk |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | RETRANSMIT |
| Subcategory | FIFOs |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Pin Count | 28 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Memory Size | 4kB |
| Element Configuration | Dual |
| Nominal Supply Current | 100mA |
| Max Supply Current | 100mA |
| Frequency (Max) | 25MHz |
| Access Time | 30 ns |
| Data Bus Width | 9b |
| Density | 4.5 kb |
| Standby Current-Max | 0.0009A |
| Screening Level | MIL-STD-883 Class B |
| Parallel/Serial | PARALLEL |
| Sync/Async | Asynchronous |
| Word Size | 9b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| FWFT Support | No |
| Output Enable | NO |
| Cycle Time | 40 ns |
| Height Seated (Max) | 5.08mm |
| Length | 37.2mm |
| Width | 15.24mm |
| Thickness | 1.65mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 28 |
7201LA30DB Overview
The CDIP package contains FIFO memory chip.In terms of packaging, it comes in Bulk cases.There is a 4kB MB memory on the FIFO chips, which can be used to store both applications and data.A Through Hole mounting method is recommended.An input voltage of 5V results in high efficiency.FIFO means contains a total of 28 terminations.As far as the operation pins are concerned, they are 28 pins.In order to operate FIFO design, a maximum current of 100mA is required.The supply voltage should be set to 5V in order to achieve FIFO's maximum efficiency.The FIFO products must be run at a minimum temperature of -55°C degrees Celsius to ensure reliability.An operating temperature of 125°C °C is necessary for stable operation.In FIFOs , this gadget is self-contained.It has a OTHER FIFO memory type IC.FIFO may operate at a very low supply voltage, such as 4.5V V.This FIFO memory chip can handle maximum supply voltages of 5.5V volts.There are a total of 28 pins on this FIFO memory IC.Regular operation has a FIFO memory's maximum value of 25MHz .There are normally 5V power supplies attached to the component.This gadget can also be used to generate RETRANSMIT .Using 1 circuits gives FIFO memory chip enhanced flexibility.
7201LA30DB Features
4kB memory size
FIFOs category
Frequency at most
7201LA30DB Applications
There are a lot of Integrated Device Technology (IDT) 7201LA30DB FIFOs Memory applications.
- MP3 Interface for Automobile
- Analog-to-digital converters
- Measurement Equipment
- Firmware loaders
- Character generators
- SPD for DDR3 Memory Modules
- Down-Hole Energy Drilling
- Queues for communication systems
- Digital buffering
- Programmable Logic Controller
