7202LA25JI
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | PLCC |
| Number of Pins | 32 |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 32 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | RETRANSMIT |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 32 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Element Configuration | Dual |
| Nominal Supply Current | 80mA |
| Max Supply Current | 80mA |
| Clock Frequency | 28.5MHz |
| Access Time | 25 ns |
| Organization | 1KX9 |
| Density | 9 kb |
| Standby Current-Max | 0.0005A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Asynchronous |
| Word Size | 9b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| Programmable Flags Support | No |
| Output Enable | NO |
| Cycle Time | 35 ns |
| Height Seated (Max) | 3.55mm |
| Length | 13.97mm |
| Width | 11.43mm |
| Thickness | 2.79mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
7202LA25JI Overview
The PLCC package contains FIFO memory chip.A Surface Mount mounting method is recommended.An input voltage of 5V results in high efficiency.A total of 32 terminations are contained within FIFO means.Operation pins are 32 .The maximum current required for its operation is 80mA .A voltage of 5V should be used for FIFO's maximum efficiency.The FIFO products must be run at a minimum temperature of -40°C degrees Celsius to ensure reliability.Keeping the operating temperature at 85°C °C allows the FIFO products to operate continuously.In FIFOs , this gadget is self-contained.ICs of type OTHER FIFO are used in the FIFO memory chip.In some cases, FIFO operates at a very low supply voltage, such as 4.5V V.This FIFO memory chip can handle maximum supply voltages of 5.5V volts.There are a total of 32 pins on this board.Normally, 5V power supplies are owned by the component.With the help of this FIFO memory, RETRANSMIT can also be generated.There is 28.5MHz frequency set for the clock of the FIFO memory IC.
7202LA25JI Features
FIFOs category
Clock frequency of 28.5MHz
7202LA25JI Applications
There are a lot of Integrated Device Technology (IDT) 7202LA25JI FIFOs Memory applications.
- Down-Hole Energy Drilling
- Disk Controllers
- IP Radio
- Extended product-change notification
- Transistors
- Consumer Systems
- Routers
- General Data Collection Applications at Extreme High-Temperatures
- Switches
- SPD for DDR3 Memory Modules
