7203L25JI8
| Parameters | |
|---|---|
| Height Seated (Max) | 3.55mm |
| Length | 13.97mm |
| Width | 11.43mm |
| Thickness | 2.79mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | PLCC |
| Number of Pins | 32 |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 32 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | RETRANSMIT |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Pin Count | 32 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Element Configuration | Dual |
| Nominal Supply Current | 120mA |
| Max Supply Current | 120mA |
| Clock Frequency | 28.5MHz |
| Access Time | 25 ns |
| Organization | 2KX9 |
| Density | 18 kb |
| Standby Current-Max | 0.002A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Asynchronous |
| Word Size | 9b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| FWFT Support | No |
| Output Enable | NO |
| Cycle Time | 35 ns |
7203L25JI8 Overview
PLCC is the package in which FIFO memory chip is contained.It is recommended that memory IC be mounted in the Surface Mount direction.When the supply voltage is 5V , high efficiency is possible.A total of 32 terminations can be found in FIFO means.32 pins are the operation pins.There is a maximum current requirement of 120mA for its operation.A supply voltage of 5V is recommended for FIFO's maximum efficiency.This FIFO products runs at -40°C degrees Celsius at a minimum temperature to ensure reliability.The stable operation is enabled by the memory logic's maximum operating temperature of 85°C °C.A self-contained gadget is contained within FIFOs .It has a OTHER FIFO memory type IC.Typically, FIFO would work at 4.5V volts, but it may also work at higher voltages.The FIFO memory chip is capable of handling maximum supply voltages of 5.5V volts.There are a total of 32 pins on this board.Normaly, the component is powered by 5V power supplies.Additionally, RETRANSMIT can be generated with this FIFO memory.FIFO memory ICs run at a frequency of 28.5MHz .
7203L25JI8 Features
FIFOs category
Clock frequency of 28.5MHz
7203L25JI8 Applications
There are a lot of Integrated Device Technology (IDT) 7203L25JI8 FIFOs Memory applications.
- IP Radio
- Extended product life cycle
- Address mapping
- Industrial Systems
- SPI Bus Flash Memory Device
- A/D output buffers
- Test Equipment
- Networking
- IP Camera Buffer
- Firmware loaders
