72215LB15PF8
| Parameters | |
|---|---|
| Height Seated (Max) | 1.6mm |
| Length | 14mm |
| Width | 14mm |
| Thickness | 1.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 64 |
| Packaging | Tape & Reel |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 64 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| HTS Code | 8542.32.00.71 |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.8mm |
| Frequency | 66.7MHz |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 64 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Element Configuration | Dual |
| Nominal Supply Current | 60mA |
| Max Supply Current | 60mA |
| Frequency (Max) | 66.7MHz |
| Access Time | 10 ns |
| Organization | 512X18 |
| Density | 9 kb |
| Standby Current-Max | 0.005A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Synchronous |
| Word Size | 18b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| FWFT Support | No |
| Programmable Flags Support | Yes |
| Output Enable | YES |
| Cycle Time | 15 ns |
72215LB15PF8 Overview
FIFO memory chip is included in the TQFP package.This FIFO memory chip is packaged as a Tape & Reel .Mounting it in the Surface Mount way is recommended.If the supply voltage is set to 5V , high efficiency can be achieved.FIFO consists of 64 terminations, which indicates that FIFO means is empty.There are 64 pins on the operation pins.In order for FIFO design to operate, a maximum current of 60mA is required.The supply voltage should be set to 5V in order to achieve FIFO's maximum efficiency.At a minimum working temperature of 0°C degrees Celsius, FIFO is guaranteed to operate reliably.An operating temperature of 70°C °C is necessary for stable operation.This gadget is self-contained in?FIFOs .This part has a memory type of OTHER FIFO .Typically, FIFO would work at 4.5V volts, but it may also work at higher voltages.The memory logic's maximum supply voltage is 5.5V volts.It has a total of 64 pins on it.With a frequency of 66.7MHz , it maintains good accuracy.It is recommended that the FIFO memory's maximum value be set to 66.7MHz .Normally, 5V power supplies are owned by the component.
72215LB15PF8 Features
FIFOs category
Frequency at most
72215LB15PF8 Applications
There are a lot of Integrated Device Technology (IDT) 72215LB15PF8 FIFOs Memory applications.
- Multi-stage synchronizer
- Measurement Equipment
- Laser Receiver System
- IP Radio
- General Data Collection Applications at Low-Temperatures
- Test Equipment
- SPI Bus Flash Memory Device
- Address mapping
- Network switching/routing
- Network bridges
