72V285L10TF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 64 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 64 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| HTS Code | 8542.32.00.71 |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 100MHz |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 64 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Element Configuration | Dual |
| Nominal Supply Current | 60mA |
| Max Supply Current | 60mA |
| Frequency (Max) | 100MHz |
| Access Time | 6.5 ns |
| Density | 1.1 Mb |
| Standby Current-Max | 0.015A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Synchronous |
| Word Size | 18b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| Output Enable | YES |
| Cycle Time | 10 ns |
| Height Seated (Max) | 1.6mm |
| Length | 10mm |
| Width | 10mm |
| Thickness | 1.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
72V285L10TF Overview
You can find FIFO memory chip in package TQFP .Mounting it in the Surface Mount way is recommended.An input voltage of 3.3V results in high efficiency.A total of 64 terminations can be found in FIFO means.There are 64 pins on the operation pins.FIFO requires a minimum of 60mA current to operate.When setting the supply voltage to 3.3V , you will achieve FIFO's maximum efficiency.It is designed to run at a minimum temperature of 0°C degrees Celsius to ensure reliability.By using a memory logic's maximum operating temperature of 70°C degrees Celsius, stable operation can be achieved.It is self-contained in FIFOs .ICs of type OTHER FIFO are used in the FIFO memory chip.The FIFO memory chip may be operated at very low supply voltages, such as3V volts.An input voltage of 3.6V V is the maximum that FIFO memory can handle.This FIFO memory IC is equipped with 64 pins in total.When the frequency is set to 100MHz it can maintain good accuracy.During normal operation, the FIFO memory's maximum value is 100MHz .
72V285L10TF Features
FIFOs category
Frequency at most
72V285L10TF Applications
There are a lot of Integrated Device Technology (IDT) 72V285L10TF FIFOs Memory applications.
- Network switching/routing
- Multimedia
- Test site
- Data-acquisition systems
- Computer Systems
- Address mapping
- IP Radio
- Video Processing
- SPD for DDR3 Memory Modules
- SPI Bus Flash Memory Devices
