74ABT16374CMTD
| Parameters | |
|---|---|
| Frequency | 150MHz |
| Base Part Number | 74ABT16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.2 ns |
| Turn On Delay Time | 6.2 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2mA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 6.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Supplier Device Package | 48-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ABT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
74ABT16374CMTD Overview
The package is in the form of 48-TFSOP (0.240, 6.10mm Width). As part of the package Tube, it is embedded. T flip flop uses Tri-State, Non-Invertedas its output configuration. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. The operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. JK flip flop belongs to the 74ABTseries of FPGAs. In order for it to function properly, its output frequency should not exceed 150MHz. In total, there are 2 elements. It consumes 2mA of quiescent The 74ABT16374 family contains this object. Its input capacitance is 5pF farads. This electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 48. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There are 8bits in this flip flop. Its superior flexibility is attributed to its use of 8 circuits. For high efficiency, the supply voltage should be set to 5V. To operate, the chip has a total of 3 output lines. It is reported that there are 2 input lines. In this case, the high level output current is set to -32mA. In the low level output current setting, 64mAis used. Ideally, the operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. The system operates with a minimum supply voltage of 4.5V. 5.5Vis its maximum supply voltage. It is possible to achieve 150MHz frequencies.
74ABT16374CMTD Features
Tube package
74ABT series
48 pins
8 Bits
74ABT16374CMTD Applications
There are a lot of ON Semiconductor 74ABT16374CMTD Flip Flops applications.
- Frequency division
- High Performance Logic for test systems
- ESD protection
- Power down protection
- Cold spare funcion
- Count Modes
- Balanced 24 mA output drivers
- Memory
- Single Down Count-Control Line
- Storage registers
