74ABT377ADB,118
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ABT377 |
| JESD-30 Code | R-PDSO-G20 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Clock Frequency | 250MHz |
| Family | ABT |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Output Polarity | TRUE |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 3.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Propagation Delay (tpd) | 4.9 ns |
| Power Supply Current-Max (ICC) | 30mA |
| fmax-Min | 250 MHz |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
74ABT377ADB,118 Overview
It is embeded in 20-SSOP (0.209, 5.30mm Width) case. You can find it in the Tape & Reel (TR)package. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74ABTseries contain this type of chip. You should not exceed 250MHzin the output frequency of the device. A total of 1elements are present in it. It consumes 250μA of quiescent There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74ABT377 family contains it. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the ABTfamily. The part is included in FF/Latches. There is a 5.5Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 4.5V. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. As an additional reference, you may refer to electronic flip flop WITH HOLD MODE.
74ABT377ADB,118 Features
Tape & Reel (TR) package
74ABT series
5V power supplies
74ABT377ADB,118 Applications
There are a lot of NXP USA Inc. 74ABT377ADB,118 Flip Flops applications.
- Memory
- Computers
- Communications
- Shift Registers
- Power down protection
- Bounce elimination switch
- QML qualified product
- Consumer
- Data storage
- Reduced system switching noise
