74ABT574CSJ
| Parameters | |
|---|---|
| Max Propagation Delay @ V, Max CL | 5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ABT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 200MHz |
| Base Part Number | 74ABT574 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 5 ns |
| Turn On Delay Time | 3.2 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 50μA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
74ABT574CSJ Overview
The package is in the form of 20-SOIC (0.209, 5.30mm Width). There is an embedded version in the package Tube. As configured, the output uses Tri-State, Inverted. The trigger it is configured with uses Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. The operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. It belongs to the 74ABTseries of FPGAs. Its output frequency should not exceed 200MHz Hz. There are 1 elements in it. It consumes 50μA of quiescent current without being affected by external factors. D latch belongs to the 74ABT574 family. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. A Positive Edgeclock edge trigger is used in this device. The design is based on 8bits. 8 circuits are used to achieve its superior flexibility. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. There are no output lines on the JK flip flop. Currently, there are 1 input lines present. A high level output current of -32mAis set. 64mAis set as the low level output current. The operating temperature should be lower than 85°C. The operating temperature should be higher than -40°C. The minimum voltage required for operation is 4.5V. In this case, it supports a maximum supply voltage of 5.5V. This can be achieved at a frequency of 200MHz.
74ABT574CSJ Features
Tube package
74ABT series
20 pins
8 Bits
74ABT574CSJ Applications
There are a lot of ON Semiconductor 74ABT574CSJ Flip Flops applications.
- Load Control
- Test & Measurement
- Automotive
- Reduced system switching noise
- Memory
- Functionally equivalent to the MC10/100EL29
- Registers
- Asynchronous counter
- Modulo – n – counter
- Computing
