74ABT74PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ABT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 250MHz |
| Propagation Delay | 3 ns |
| Quiescent Current | 50μA |
| Turn On Delay Time | 3 ns |
| Family | ABT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 15mA 20mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 4.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.05mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74ABT74PW,118 Overview
The flip flop is packaged in 14-TSSOP (0.173, 4.40mm Width). A package named Tape & Reel (TR)includes it. It is configured with Differentialas an output. This trigger is configured to use Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. In this case, the operating temperature is -40°C~85°C TA. This D latch has the type D-Type. In this case, it is a type of FPGA belonging to the 74ABT series. You should not exceed 250MHzin its output frequency. The number of terminations is 14. The 74ABT74 family contains it. Power is provided by a 5V supply. A 3pFfarad input capacitance is provided by this T flip flop. ABTis the family of this D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. There are 14pins on it. This device has Positive Edgeas its clock edge trigger type. The superior flexibility is achieved through the use of 2 circuits. Optimal efficiency requires a supply voltage of 5V. In order to operate, the chip has 1 output lines. As a result, it consumes 50μA of quiescent current without being affected by external factors.
74ABT74PW,118 Features
Tape & Reel (TR) package
74ABT series
14 pins
74ABT74PW,118 Applications
There are a lot of Nexperia USA Inc. 74ABT74PW,118 Flip Flops applications.
- Latch
- Shift registers
- Data transfer
- Differential Individual
- Single Up Count-Control Line
- Parallel data storage
- 2 – Bit synchronous counter
- Latch-up performance
- Balanced Propagation Delays
- Consumer
