74AC109PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | JK Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 175MHz |
| Base Part Number | 74AC109 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 2 |
| Clock Frequency | 175MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | AND, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 5 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC109PC Overview
The flip flop is packaged in a case of 16-DIP (0.300, 7.62mm). As part of the package Tube, it is embedded. This output is configured with Differential. This trigger is configured to use Positive Edge. In this case, the electronic component is mounted in the way of Through Hole. A voltage of 2V~6Vis required for its operation. Temperature is set to -40°C~85°C TA. The type of this D latch is JK Type. The FPGA belongs to the 74AC series. Its output frequency should not exceed 175MHz. In total, it contains 2 elements. It consumes 2μA of quiescent D latch belongs to the 74AC109 family. Its input capacitance is 4.5pFfarads. There is an electronic part mounted in the way of Through Hole. With its 16pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is designed with a number of bits of 2. To achieve this superior flexibility, 2 circuits are used. To operate, the chip has a total of 2 output lines. A total of 5input lines have been provided. High level output current is set to -24mA. Low level output current is set to 24mA. The operating temperature should be lower than 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. It operates with the minimal supply voltage of 2V. 6Vis the maximum supply voltage it supports. 175MHzis the maximum frequency that can be achieved.
74AC109PC Features
Tube package
74AC series
16 pins
2 Bits
74AC109PC Applications
There are a lot of ON Semiconductor 74AC109PC Flip Flops applications.
- ESCC
- Shift registers
- ATE
- Memory
- Digital electronics systems
- Parallel data storage
- Registers
- Bus hold
- Patented noise
- Single Up Count-Control Line
