74AC11074NSR
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 3V |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 150MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 4.2 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 7.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC11074 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
74AC11074NSR Overview
The package is in the form of 14-SOIC (0.209, 5.30mm Width). As part of the package Tape & Reel (TR), it is embedded. There is a Differentialoutput configured with it. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates at 3V~5.5Vvolts. A temperature of -40°C~85°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74AC series. There should be no greater frequency than 150MHzon its output. In total, it contains 2 elements. It consumes 4μA of quiescent current without being affected by external factors. Currently, there are 14 terminations. The 74AC11074family includes it. Power is supplied from a voltage of 5V volts. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family ACcan be found here. This electronic part is mounted in the way of Surface Mount. This board is designed with 14pins on it. This device exhibits a clock edge trigger type of Positive Edge. This part is included in FF/Latches. This flip flop is designed with 1 Bits. It reaches 5.5Vwhen the supply voltage is maximal (Vsup). The supply voltage (Vsup) should be maintained above 3V for normal operation. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. In order for the device to operate, it requires 3.3/5V power supplies. It has 1 output lines to operate.
74AC11074NSR Features
Tape & Reel (TR) package
74AC series
14 pins
1 Bits
3.3/5V power supplies
74AC11074NSR Applications
There are a lot of Texas Instruments 74AC11074NSR Flip Flops applications.
- Memory
- Circuit Design
- High Performance Logic for test systems
- Single Down Count-Control Line
- Shift Registers
- Instrumentation
- Data storage
- Frequency Divider circuits
- Supports Live Insertion
- Communications
