74AC11074NSRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC11074 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 3V |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 150MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 4.2 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 7.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
74AC11074NSRG4 Overview
The flip flop is packaged in a case of 14-SOIC (0.209, 5.30mm Width). There is an embedded version in the package Tape & Reel (TR). Currently, the output is configured to use Differential. JK flip flop uses Positive Edgeas the trigger. Surface Mountis occupied by this electronic component. The JK flip flop operates at a voltage of 3V~5.5V. In the operating environment, the temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. In FPGA terms, D flip flop is a type of 74ACseries FPGA. Its output frequency should not exceed 150MHz. A total of 2elements are present in it. It consumes 4μA of quiescent current without being affected by external factors. A total of 14terminations have been recorded. The 74AC11074 family contains it. A voltage of 5V is used to power it. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the ACfamily. There is an electronic part that is mounted in the way of Surface Mount. A total of 14pins are provided on this board. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latches. The flip flop is designed with 1bits. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be above 3V. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. It runs on 3.3/5Vvolts of power. There are no output lines on the JK flip flop.
74AC11074NSRG4 Features
Tape & Reel (TR) package
74AC series
14 pins
1 Bits
3.3/5V power supplies
74AC11074NSRG4 Applications
There are a lot of Texas Instruments 74AC11074NSRG4 Flip Flops applications.
- Computers
- Digital electronics systems
- Convert a momentary switch to a toggle switch
- Set-reset capability
- Supports Live Insertion
- Differential Individual
- Memory
- Frequency division
- CMOS Process
- ATE
