74AC174MTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | TIN |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC174 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 250MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74AC174MTR Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Non-Invertedas its output configuration. It is configured with a trigger that uses a value of Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~6V. A temperature of -55°C~125°C TAis considered to be the operating temperature. It belongs to the type D-Typeof flip flops. In terms of FPGAs, it belongs to the 74AC series. In order for it to function properly, its output frequency should not exceed 250MHz. D latch consists of 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. A total of 16terminations have been recorded. The 74AC174 family contains this object. The D flip flop is powered by a voltage of 3.3V . There is 4.5pF input capacitance for this T flip flop. Devices in the ACfamily are electronic devices. There is an electronic component mounted in the way of Surface Mount. 16pins are included in its design. The clock edge trigger type for this device is Positive Edge. It is included in FF/Latches. The design is based on 6bits. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be above 2V. The superior flexibility of this circuit is achieved by using 7 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. It operates from 3.3/5V power supplies. It operates with 6 output lines.
74AC174MTR Features
Tape & Reel (TR) package
74AC series
16 pins
6 Bits
3.3/5V power supplies
74AC174MTR Applications
There are a lot of STMicroelectronics 74AC174MTR Flip Flops applications.
- Frequency division
- Memory
- Frequency Divider circuits
- Balanced Propagation Delays
- Balanced 24 mA output drivers
- Communications
- Latch
- Consumer
- Test & Measurement
- Divide a clock signal by 2 or 4
