74AC174PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 125MHz |
| Base Part Number | 74AC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Output Current | 24mA |
| Number of Bits | 6 |
| Clock Frequency | 125MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC174PC Overview
16-DIP (0.300, 7.62mm)is the packaging method. The Tubepackage contains it. As configured, the output uses Non-Inverted. It is configured with the trigger Positive Edge. It is mounted in the way of Through Hole. The JK flip flop operates at 2V~6Vvolts. It is operating at a temperature of -40°C~85°C TA. This electronic flip flop is of type D-Type. In this case, it is a type of FPGA belonging to the 74AC series. In order for it to function properly, its output frequency should not exceed 125MHz. The list contains 1 elements. T flip flop consumes 40μA quiescent energy. The object belongs to the 74AC174 family. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is mounted by the way of Through Hole. The 16pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There are 6bits in its design. To achieve this superior flexibility, 7 circuits are used. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. In order for the chip to function, it has 6output lines. It is reported that there are 3 input lines. A high level output current of -24mAis set. It is set to 24mAfor low level output current. Ideally, the operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. The system operates with a minimum supply voltage of 2V. It supports the maximal supply voltage of 6V. This can be achieved at a frequency of 125MHz.
74AC174PC Features
Tube package
74AC series
16 pins
6 Bits
74AC174PC Applications
There are a lot of ON Semiconductor 74AC174PC Flip Flops applications.
- Synchronous counter
- Safety Clamp
- Common Clocks
- Latch
- Instrumentation
- Frequency Divider circuits
- Shift registers
- Frequency Dividers
- ESD protection
- Set-reset capability
