74AC374SJ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 155MHz |
| Base Part Number | 74AC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 8 |
| Clock Frequency | 155MHz |
| Propagation Delay | 13.5 ns |
| Turn On Delay Time | 8 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC374SJ Overview
20-SOIC (0.209, 5.30mm Width)is the way it is packaged. You can find it in the Tubepackage. There is a Tri-State, Non-Invertedoutput configured with it. JK flip flop uses Positive Edgeas the trigger. It is mounted in the way of Surface Mount. With a supply voltage of 2V~6V volts, it operates. A temperature of -40°C~85°C TAis used in the operation. There is D-Type type of electronic flip flop associated with this device. JK flip flop is a part of the 74ACseries of FPGAs. There should be no greater frequency than 155MHzon its output. A total of 1 elements are present. As a result, it consumes 40μA quiescent current and is not affected by external forces. If you search by 74AC374, you will find similar parts. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This electronic part is mounted in the way of Surface Mount. There are 20pins on it. It has a clock edge trigger type of Positive Edge. There are 8bits in this flip flop. The superior flexibility of this circuit is achieved by using 8 circuits. In order to operate, the chip has 8 output lines. A total of 1input lines have been provided. A high level output current of -24mAis set. 24mAis set as the low level output current. A temperature below 85°Cshould be used for operation. A temperature above -40°Cshould be used for the operation. It is powered by 2V as its minimum supply voltage. 6Vis the maximum supply voltage supported by it. It is possible to obtain a frequency of 155MHz.
74AC374SJ Features
Tube package
74AC series
20 pins
8 Bits
74AC374SJ Applications
There are a lot of ON Semiconductor 74AC374SJ Flip Flops applications.
- Control circuits
- Count Modes
- Set-reset capability
- Registers
- Power down protection
- High Performance Logic for test systems
- Communications
- Divide a clock signal by 2 or 4
- Buffer registers
- ESD protection
