74AC574PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Supplier Device Package | 20-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 153MHz |
| Base Part Number | 74AC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 153MHz |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Frequency | 85MHz |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC574PC Overview
As a result, it is packaged as 20-DIP (0.300, 7.62mm). You can find it in the Tubepackage. In the configuration, Tri-State, Non-Invertedis used as the output. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Through Hole. The JK flip flop operates with an input voltage of 2V~6V volts. It is operating at -40°C~85°C TA. This logic flip flop is classified as type D-Type. In terms of FPGAs, it belongs to the 74AC series. Its output frequency should not exceed 153MHz. There are 1 elements in it. It consumes 40μA of quiescent The 74AC574 family contains it. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A part of the electronic system is mounted in the way of Through Hole. As you can see from the design, it has pins with 20. In this device, the clock edge trigger type is Positive Edge. It is designed with 8bits. Its flexibility is enhanced by 8 circuits. Its output current of 24mAallows for maximum design flexibility. In order for the chip to function, it has 3output lines. It is reported that there are 1 input lines. -24mAis the output current at high level. In the low level output current setting, 24mAis used. It is recommended that the operating temperature be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. It operates with the minimal supply voltage of 2V. 6Vis the maximum supply voltage it supports. It is possible to achieve a frequency of 153MHz.
74AC574PC Features
Tube package
74AC series
20 pins
8 Bits
74AC574PC Applications
There are a lot of ON Semiconductor 74AC574PC Flip Flops applications.
- Circuit Design
- Shift registers
- Matched Rise and Fall
- High Performance Logic for test systems
- Patented noise
- Latch-up performance
- Dynamic threshold performance
- Data Synchronizers
- Individual Asynchronous Resets
- Latch
