74AC74PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | Through Hole |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 160MHz |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Output Current | 24mA |
| Number of Bits | 2 |
| Clock Frequency | 160MHz |
| Propagation Delay | 16 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Number of Inputs | 1 |
| Current - Output High, Low | 24mA 24mA |
| Number of Gates | 2 |
| Number of Bits per Element | 1 |
| Max Frequency | 125MHz |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC74PC Overview
14-DIP (0.300, 7.62mm)is the packaging method. D flip flop is embedded in the Tube package. T flip flop uses Differentialas the output. There is a trigger configured with Positive Edge. In this case, the electronic component is mounted in the way of Through Hole. A voltage of 2V~6Vis required for its operation. In this case, the operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. It belongs to the 74ACseries of FPGAs. In order for it to function properly, its output frequency should not exceed 160MHz. In total, there are 2 elements. During its operation, it consumes 20μA quiescent energy. It is a member of the 74AC74 family. The input capacitance of this JK flip flopis 4.5pF farads. There is an electronic part that is mounted in the way of Through Hole. There are 14pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The design is based on 2bits. To achieve this superior flexibility, 2 circuits are used. With a current output of 24mA , it offers maximum design flexibility. To operate, the chip has a total of 2 output lines. 4input lines are available for you to choose from. -24mAis the output current at high level. In the low level output current setting, the current is set to 24mA. The operating temperature should be lower than 85°C. Temperatures above -40°Cshould be used. A minimum supply voltage of 2V is required for these RS flip flops to operate. There is a maximum voltage support of 6V. It is possible to achieve 160MHz frequencies. The building block contains a total of 2 gates. There are 1 inputs involved.
74AC74PC Features
Tube package
74AC series
14 pins
2 Bits
2 gates
74AC74PC Applications
There are a lot of ON Semiconductor 74AC74PC Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Supports Live Insertion
- Data transfer
- ATE
- Circuit Design
- Computers
- Count Modes
- EMI reduction circuitry
- Storage Registers
- QML qualified product
