74AC74SCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Supplier Device Package | 14-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 125MHz |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 2 |
| Clock Frequency | 160MHz |
| Propagation Delay | 16 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Frequency | 125MHz |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC74SCX Overview
The flip flop is packaged in a case of 14-SOIC (0.154, 3.90mm Width). D flip flop is embedded in the Tape & Reel (TR) package. In the configuration, Differentialis used as the output. Positive Edgeis the trigger it is configured with. Surface Mountis positioned in the way of this electronic part. A supply voltage of 2V~6V is required for operation. Currently, the operating temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74ACseries FPGA. Its output frequency should not exceed 160MHz. A total of 2elements are present in it. It consumes 20μA of quiescent current without being affected by external factors. JK flip flop belongs to 74AC74 family. The input capacitance of this JK flip flopis 4.5pF farads. The electronic part is mounted in the way of Surface Mount. It is designed with 14 pins. This device exhibits a clock edge trigger type of Positive Edge. An electronic part designed with 2bits is used in this application. In order to achieve its superior flexibility, 2 circuits are used. In order to operate, the chip has 2 output lines. Currently, there are 4 lines of input. There is -24mA output current at the high level. It is set to 24mAfor low level output current. There should be a temperature below 85°Cduring operation. The operating temperature should be higher than -40°C. It is powered by 2V as its minimum supply voltage. It supports a maximum supply voltage of 6V volts. The frequency that can be achieved is 125MHz.
74AC74SCX Features
Tape & Reel (TR) package
74AC series
14 pins
2 Bits
74AC74SCX Applications
There are a lot of ON Semiconductor 74AC74SCX Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Buffer registers
- QML qualified product
- High Performance Logic for test systems
- Consumer
- Set-reset capability
- Bounce elimination switch
- Divide a clock signal by 2 or 4
- Latch-up performance
- 2 – Bit synchronous counter
