74ACQ574SCX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACQ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 85MHz |
| Base Part Number | 74ACQ574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Frequency | 85MHz |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACQ574SCX Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. There is an embedded version in the package Tape & Reel (TR). In the configuration, Tri-State, Non-Invertedis used as the output. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates at 2V~6Vvolts. A temperature of -40°C~85°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. JK flip flop is a part of the 74ACQseries of FPGAs. There should be no greater frequency than 90MHzon its output. D latch consists of 1 elements. It consumes 40μA of quiescent current without being affected by external factors. JK flip flop belongs to 74ACQ574 family. Input capacitance of this device is 4.5pF farads. Surface Mount mounts this electronic component. This board is designed with 20pins on it. There is a clock edge trigger type of Positive Edgeon this device. The design is based on 8bits. The superior flexibility of this product is achieved by using 8 circuits. There are 8 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. It has 1lines. A -24mAis set for the high level output current. In the low level output current setting, the current is set to 24mA. Temperatures below 85°Care ideal for operating. Ideally, the operating temperature should be greater than -40°C. A minimum supply voltage of 2V is required for these RS flip flops to operate. The maximum supply voltage supported by the flip flop is 6V. The frequency that can be achieved is 85MHz.
74ACQ574SCX Features
Tape & Reel (TR) package
74ACQ series
20 pins
8 Bits
74ACQ574SCX Applications
There are a lot of ON Semiconductor 74ACQ574SCX Flip Flops applications.
- Storage registers
- Convert a momentary switch to a toggle switch
- Reduced system switching noise
- ATE
- Event Detectors
- Patented noise
- Test & Measurement
- Count Modes
- Shift registers
- Frequency division
