74ACT11074DBR
| Parameters | |
|---|---|
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT11074 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 125MHz |
| Propagation Delay | 8.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 5.7 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 121.789551mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
74ACT11074DBR Overview
It is packaged in the way of 14-SSOP (0.209, 5.30mm Width). There is an embedded version in the package Cut Tape (CT). T flip flop is configured with an output of Differential. It is configured with a trigger that uses a value of Positive Edge. It is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. The operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. The 74ACTseries comprises this type of FPGA. Its output frequency should not exceed 125MHz Hz. A total of 14 terminations have been made. The 74ACT11074 family contains it. The D flip flop is powered by a voltage of 5V . Its input capacitance is 3.5pFfarads. An electronic device belonging to the family ACTcan be found here. There is an electronic component mounted in the way of Surface Mount. The electronic flip flop is designed with pins 14. This device has the clock edge trigger type of Positive Edge. The part is included in FF/Latches. 2 circuits are used to achieve its superior flexibility. Considering the reliability of this T flip flop, it is well suited for TR. The system runs on a power supply of 5V watts. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. With an output current of 24mA, this device offers maximum design flexibility. It has 1 output lines to operate. This D latch consumes 4μA quiescent current at all.
74ACT11074DBR Features
Cut Tape (CT) package
74ACT series
14 pins
5V power supplies
74ACT11074DBR Applications
There are a lot of Texas Instruments 74ACT11074DBR Flip Flops applications.
- Counters
- Guaranteed simultaneous switching noise level
- Buffered Clock
- Set-reset capability
- Registers
- Individual Asynchronous Resets
- Consumer
- Test & Measurement
- Pattern generators
- Divide a clock signal by 2 or 4
