74ACT11074DG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT11074 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 125MHz |
| Propagation Delay | 8.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 5.7 ns |
| Family | ACT |
| Logic Function | AND, D-Type |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74ACT11074DG4 Overview
It is packaged in the way of 14-SOIC (0.154, 3.90mm Width). The package Tubecontains it. Currently, the output is configured to use Differential. It is configured with a trigger that uses a value of Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates at 4.5V~5.5Vvolts. It is operating at -40°C~85°C TA. This D latch has the type D-Type. It belongs to the 74ACTseries of FPGAs. Its output frequency should not exceed 125MHz. There are 14 terminations,This D latch belongs to the family of 74ACT11074. The power source is powered by 5V. The input capacitance of this JK flip flopis 3.5pF farads. This D flip flop belongs to the family of ACT. There is an electronic part that is mounted in the way of Surface Mount. 14pins are included in its design. This device has Positive Edgeas its clock edge trigger type. This device has the base part number FF/Latches. Due to its superior flexibility, it uses 2 circuits. The D latch runs on a voltage of 5V volts. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. Its output current of 24mAallows for maximum design flexibility. In order for the chip to function, it has 1output lines. Quiescent current is consumed by the D latch in the amount of 4μA.
74ACT11074DG4 Features
Tube package
74ACT series
14 pins
5V power supplies
74ACT11074DG4 Applications
There are a lot of Texas Instruments 74ACT11074DG4 Flip Flops applications.
- Instrumentation
- EMI reduction circuitry
- Balanced Propagation Delays
- Clock pulse
- Memory
- Control circuits
- Divide a clock signal by 2 or 4
- Storage Registers
- Count Modes
- Buffered Clock
