74ACT11074DRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT11074 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 125MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 5.7 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
74ACT11074DRE4 Overview
It is packaged in the way of 14-SOIC (0.154, 3.90mm Width). As part of the package Tape & Reel (TR), it is embedded. There is a Differentialoutput configured with it. It is configured with the trigger Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. A temperature of -40°C~85°C TAis used in the operation. It is an electronic flip flop with the type D-Type. It is a type of FPGA belonging to the 74ACT series. A frequency of 125MHzshould be the maximum output frequency. During its operation, it consumes 4μA quiescent energy. In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 74ACT11074, you will find similar parts. It is powered by a voltage of 5V . JK flip flop input capacitance is 3.5pF farads. A device of this type belongs to the family of ACT. Surface Mount mounts this electronic component. A total of 14pins are provided on this board. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The superior flexibility is achieved through the use of 2 circuits. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. An electrical current of 5V volts is applied to it. The supply voltage should be maintained at 5V for high efficiency. The 24mA output current allows it to be designed with the greatest amount of flexibility. To operate, the chip has a total of 1 output lines.
74ACT11074DRE4 Features
Tape & Reel (TR) package
74ACT series
14 pins
5V power supplies
74ACT11074DRE4 Applications
There are a lot of Texas Instruments 74ACT11074DRE4 Flip Flops applications.
- Memory
- Modulo – n – counter
- Storage Registers
- EMI reduction circuitry
- Asynchronous counter
- Count Modes
- Safety Clamp
- Test & Measurement
- Counters
- ESD protection
