74ACT16374DLR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| Manufacturer Package Identifier | DL0048A |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 16 |
| Clock Frequency | 65MHz |
| Propagation Delay | 13.4 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 8.8 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.79mm |
| Length | 15.88mm |
| Width | 7.49mm |
| Thickness | 2.59mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74ACT16374DLR Overview
It is embeded in 48-BSSOP (0.295, 7.50mm Width) case. It is contained within the Tape & Reel (TR)package. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. The operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. It belongs to the 74ACTseries of FPGAs. Its output frequency should not exceed 65MHz. There are 2 elements in it. In 48terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Members of the 74ACT16374family make up this object. A voltage of 5V is used to power it. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the ACTfamily. A part of the electronic system is mounted in the way of Surface Mount. There are 48pins on it. Its clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. The flip flop is designed with 16bits. Considering the reliability of this T flip flop, it is well suited for TR. The D latch runs on a voltage of 5V volts. The D flip flop is embedded with 2ports. In order to ensure high efficiency, the supply voltage should remain at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. To operate, the chip has a total of 3 output lines. As of now, there are 1input lines. It consumes 8μA current.
74ACT16374DLR Features
Tape & Reel (TR) package
74ACT series
48 pins
16 Bits
5V power supplies
74ACT16374DLR Applications
There are a lot of Texas Instruments 74ACT16374DLR Flip Flops applications.
- Computing
- Storage registers
- Consumer
- Single Up Count-Control Line
- Single Down Count-Control Line
- Shift Registers
- Frequency division
- Control circuits
- Clock pulse
- Cold spare funcion
