74ACT16374MTDX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Supplier Device Package | 48-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 71MHz |
| Base Part Number | 74ACT16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 16 |
| Clock Frequency | 71MHz |
| Propagation Delay | 7.9 ns |
| Turn On Delay Time | 5.1 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 80μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 7.9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 16 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT16374MTDX Overview
48-TFSOP (0.240, 6.10mm Width)is the packaging method. D flip flop is included in the Tape & Reel (TR)package. T flip flop uses Tri-State, Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. It is operating at -40°C~85°C TA. D-Typeis the type of this D latch. In FPGA terms, D flip flop is a type of 74ACTseries FPGA. It should not exceed 71MHzin its output frequency. In total, it contains 2 elements. As a result, it consumes 80μA quiescent current. D latch belongs to the 74ACT16374 family. Its input capacitance is 4.5pF farads. It is mounted by the way of Surface Mount. This board has 48 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The flip flop is designed with 16bits. Its superior flexibility is attributed to its use of 8 circuits. For high efficiency, the supply voltage should be kept at 5V. There are 16 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. This input has 2lines. It is set to -24mAfor the high level output current. It is set to 24mAfor low level output current. The operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. There is a maximum voltage support of 5.5V. This frequency can be achieved 71MHz.
74ACT16374MTDX Features
Tape & Reel (TR) package
74ACT series
48 pins
16 Bits
74ACT16374MTDX Applications
There are a lot of ON Semiconductor 74ACT16374MTDX Flip Flops applications.
- Automotive
- Data storage
- Instrumentation
- Clock pulse
- Power down protection
- Test & Measurement
- EMI reduction circuitry
- Bus hold
- Divide a clock signal by 2 or 4
- Circuit Design
